When something stops working in your home and you are not sure whether it is a quick fix or something deeper, the right move is a call. We handle electrical repairs, panel work, wiring, lighting, and more for homes and businesses across Draper, and the process starts the same way every time: you describe what you are seeing, we scope the job on the phone, and you get a price before anything is scheduled.
Homes in this area were wired in different decades, and it shows in the panels.
Whether you are dealing with a breaker that keeps tripping, an outlet that has never worked right, or a panel that is out of room, call (385) 452-6995 and we will walk through it with you. We are available every day from 6:30 AM to 10:00 PM.
Most people have a mental list of electrical things they have been meaning to deal with. An outlet on one wall that has never worked. A light switch near the back door that sparks faintly when you flip it. An exterior fixture that has been dark for two seasons. None of them feel urgent enough to schedule, so they stay on the list.
The outlet that never worked may be on a GFCI circuit that tripped once and was never reset, which takes five minutes to sort out. It may also be a wiring fault at the device or a break in the run, which takes longer and is worth knowing about. The switch that sparks is worth a closer look regardless of how minor it seems, because a loose connection at a switch can develop into an arc fault over time. The outside light that nobody got around to is often a weatherproofing or fixture issue, but it could be a failed GFCI outlet protecting the exterior circuit.
The point is not that every deferred job is a crisis. It is that you cannot tell which ones are until someone traces them. A call costs nothing, and the scope gets confirmed before any visit is scheduled. One call is enough to get the visit booked.
No-pressure estimates, priced up front. That is how we handle quotes, and it means the price is settled on the call, not after we arrive.
What moves a quote is what the job actually involves. A single outlet replacement is a different scope than running a new circuit from the panel to a room that has never had one. A ceiling fan swap where the box and wiring are already in place is a different job than roughing in a fan circuit in a room with no existing switch leg. For panel work, the price depends on the existing service entrance, the amperage the load calculation calls for, and whether the meter receptacle needs attention alongside the panel itself.
What the fault turns out to be matters too. A dead circuit might trace back to a tripped breaker, a failed device, or a wiring fault inside the wall. We find out which before quoting the repair, because the answer changes the work. Ask what the job covers and you get a straight answer.
Appointments are arranged on the call. You describe the situation, we scope what the visit will cover, and a time is confirmed before the call ends. If a problem will not keep, we take short-notice work and the schedule is discussed when you call. We do not promise a window we cannot stand behind, but we do tell you what is available.
For rental properties, we work around whoever is on site. That means confirming the scope with the property manager before the visit, explaining what the circuit shutoff will affect and for how long, and leaving the space the way we found it. A property manager who needs documentation of what was done gets a clear account of the work.
Commercial work in a city like Draper often means the property has to stay operational. We scope the job to identify which circuits need to be off and for how long, and we work in stages where the layout allows it. The goal is the same as any other job: the work gets done, the price is confirmed before it starts, and the result is left to code. Anything not covered here is on the services page.
The calls we get from Draper cover a range of job types. Some are repairs. Some are new installations. Some are upgrades driven by a new appliance, a new vehicle, or a panel that has run out of capacity. Each one is scoped on the call so you know what the visit involves before anyone arrives.
Battery-only alarms have a place, but hardwired detectors on an interconnected circuit mean that when one goes off, they all go off. Installation involves running the wiring between units and connecting them to a circuit with battery backup. Older Draper homes that still have standalone battery detectors in each room are good candidates for an upgrade.
The electrical side of a generator installation is the transfer switch, the dedicated circuit from the panel to the connection point, and the interlock or automatic transfer equipment that keeps the generator from feeding back onto the utility line. We size the circuit and the transfer equipment to match the load, and we confirm panel capacity before the visit is scheduled. The generator unit itself is a separate product choice. We wire it so it runs safely when the power goes out.
Recessed lighting installation means the right junction box for the ceiling type, a circuit sized for the fixture load, and clean wiring runs that do not leave the attic or ceiling space a problem for the next person who works up there. LED retrofits in existing cans are often straightforward, but older fixtures sometimes need a compatible driver or a new trim kit to work correctly with LED bulbs.
Pendant lights, chandeliers, and flush-mount fixtures all require a rated junction box and a circuit that can carry the load. Swapping a fixture for a heavier one sometimes means upgrading the box. We confirm what the existing wiring can support before the installation begins, and we tell you on the call if the job is likely to involve more than a straight swap.
An inspection gives you a documented picture of what the system is doing. That includes the panel, the branch circuits, grounding and bonding, GFCI and AFCI protection, and visible wiring conditions. Homes with knob-and-tube wiring, aluminum branch circuits, or panels that have not been touched in decades are strong candidates. The report is useful when a property changes hands, when an insurer asks for documentation, or when a homeowner simply wants to know what they are working with.
Low-voltage work covers doorbell wiring, data runs, and the rough-in for structured wiring in a new build or renovation. It sits alongside the line-voltage work rather than replacing it. If a smart doorbell needs a transformer upgrade or a new circuit to power it reliably, that is part of the same visit.
Some electrical problems are easy to reproduce. Others only happen in specific conditions, and that is what makes them harder to find.
A breaker that trips under load but holds fine when the circuit is lightly used points to a capacity issue or a wiring fault that only shows up when current is actually flowing. A circuit that fails when it rains is often a moisture intrusion problem at an exterior box or a conduit entry point. An intermittent fault that comes and goes with no clear pattern can be a loose connection that makes and breaks contact depending on temperature or vibration.
Finding these takes a different approach than a straightforward repair. We trace the circuit under the conditions that reproduce the fault, check every connection point along the run, and test the grounding and bonding before closing the job. Clear communication from the first call to the final test is how the work gets done right. Reach out and we'll start at the panel.
When a job closes, the circuit or device gets tested before we leave. For outlet work, that means checking polarity, grounding, and GFCI or AFCI function where it applies. For panel work, we confirm breaker seating, load distribution, and that the main and branch circuits are operating correctly. Breakers are labeled. Any changes to the circuit layout are noted so the next person who opens the panel knows what they are looking at.
That documentation matters more than it might seem. When a property is sold, a buyer's inspector will look at the panel and ask about any recent work. A labeled panel with a clear circuit map is a straightforward answer. An unlabeled panel with undocumented changes is a question mark that can slow a closing. We leave the panel the way it should have been left the first time.
We cover Draper and the surrounding communities throughout Salt Lake County. That includes Bluffdale, White City, Sandy, Riverton, and Alpine. Whether the property is a single-family home, a rental, or a commercial building, the work is the same: scoped on the call, priced before the visit, and done to the code that applies here.
If your address is nearby and you are not sure whether it falls within the service area, ask on the call.
Call (385) 452-6995 and describe what the follow-up is for.
If it is related to work we have already done, we treat it accordingly. If it is a new issue, we scope it on the call the same way we would any other job.
Yes. We work with property managers and landlords on repairs, circuit additions, panel work, and safety inspections across rental properties of all sizes. The scope is confirmed with the property manager before the visit, and we document the work so there is a clear record of what was done and when.
Crawl space access is sometimes necessary for circuits routed under the floor. We confirm whether crawl space access is required for the specific job on the call. If it is, we discuss what the access looks like and whether any preparation is needed before the visit.
The most useful thing is a safety inspection before you start any renovation or add any new circuits. It gives you a documented picture of the panel, the branch circuits, the grounding and bonding, and the condition of the visible wiring. If the home has older wiring or a panel that has not been updated, the inspection tells you what the system can carry and what would need to change before you add load to it.
Call (385) 452-6995 and we can walk through what the inspection covers.
It often does. Homes built in different decades were wired to the standards of their time, and those standards changed significantly across the second half of the twentieth century. Knob-and-tube wiring, aluminum branch circuits, and panels that were sized for a much lighter load than a modern household draws are all more common in older properties. An inspection tells you what the system is actually doing before you decide what, if anything, needs attention.
Describe the problem, get a price, and decide whether to schedule. That is the whole process.
Call (385) 452-6995 and a real person answers, every day from 6:30 AM to 10:00 PM.
We take calls for Draper and the surrounding area, and the rate is confirmed before anything is scheduled.
There are no forms to fill out and no waiting for a callback. Call now and we'll get the power back where it belongs.
Close by, we also take electrical work in: Bluffdale, Sandy, Riverton. Have a look at our service map.
Below is a plain-language look at the electrical services we handle across Draper and Salt Lake County. Each row covers what the work involves, who it fits best, and one practical note worth knowing before you call. If a job spans more than one category, we scope it together on the phone so nothing gets missed.
| Service | What's Included | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel & Service Upgrades |
| Homes adding an EV charger, heat tape circuits, or major appliances that push a 100-amp panel past its limit | Older Draper homes are often still on 100-amp service, which was sized for a fraction of the load that modern appliances, EV chargers, and heat tape circuits now demand. |
| Electrical Repairs & Troubleshooting |
| Homeowners dealing with flickering lights, dead outlets, or tripping breakers | A warm outlet or a burning smell calls for immediate attention, not a wait-and-see approach. |
| Garage & Block-Heater Circuits |
| Salt Lake County homeowners who need reliable power for block heaters and garage equipment through winter | Block-heater outlets need to be on a circuit sized for continuous overnight draw, not shared with general garage outlets. |
Call (385) 452-6995 between 6:30 AM and 10:00 PM any day of the week and we will go through your job with you, confirm the scope, and give you a price before anything is scheduled.
(385) 452-6995