When a business in Payson needs electrical work done, the stakes are different from a home repair. A retail space, a workshop, or a rental unit has schedules to keep and occupants to work around. The circuit that feeds the equipment cannot be down for a day while someone figures out what to do next. We handle commercial and light industrial electrical work with that in mind: the scope is confirmed on the phone, the visit is planned around what has to stay running, and the work is done in a sequence that keeps disruption to a minimum.
We take calls from property owners, contractors, and business operators across Payson. Whether the job is a subpanel for a detached workshop, new circuits for added equipment, or a panel replacement in a building that has been wired and rewired by several different hands, the approach is the same.
Call (385) 452-6995 and walk through the job with us. The price is confirmed before anything is scheduled.
This comes up more often than most people expect. A previous owner added a circuit. A contractor roughed in a subpanel without finishing it properly. An outlet was replaced but the grounding was never connected. In a town where a lot of the housing stock was built across several different decades, the wiring inside a wall does not always match what the panel says it is.
When we find work that does not meet current standards, the first step is understanding what it is doing and whether it is creating a risk right now. Some conditions need to be corrected before the job we were called for can proceed. Others are worth noting and addressing on a separate visit. We do not manufacture urgency, and we do not leave a customer guessing. What we find gets explained plainly, what it means gets explained plainly, and the customer decides how to proceed. No-pressure estimates, priced up front.
Calling an electrician doesn't have to be stressful, and the pricing conversation is a good place to start. When you call, we ask about the symptom, the location in the building, and what the existing panel and wiring look like as far as you can tell. That shapes the initial estimate. What can shift it once we are on-site is what the fault actually turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change being asked of it.
A straightforward outlet repair and a fault that turns out to trace back to a wiring problem inside the wall are two different scopes, and the price reflects that. We do not quote a number on the phone and then add to it silently once the work is underway. If the scope changes, we talk through it before the work continues. The rate is confirmed before we schedule, and any adjustment is explained before it happens.
What tends to move a quote in one direction or another:
Homes in this area were wired in different decades, and it shows in the panels. A house that has changed hands a few times, had a garage converted, or had a workshop added out back often carries wiring that was done in layers, each one reflecting the code and the habits of the person who did it. The jobs below come out of that reality.
Adding a major appliance or a piece of workshop equipment usually means adding a dedicated circuit sized for that load. A hot tub, a table saw, a welder, or a new electric range each draws more current than a standard household circuit is rated to carry. We run the circuit from the panel, install the correct outlet or connection point, and confirm the breaker is matched to the load. If the panel does not have room, that conversation happens before the circuit is run.
A detached garage or a workshop that is more than a few feet from the main building usually needs its own subpanel rather than a long circuit run back to the house. The subpanel takes a feed from the main panel and distributes it to the circuits in the outbuilding. We size the subpanel feed to what the space will actually draw, which matters when the plan includes power tools, a compressor, and lighting all running at the same time.
A panel replacement is not always about adding capacity. Sometimes a panel needs to come out because the breakers are failing, because the equipment is no longer supported, or because an inspection has flagged it as a risk. We assess what the replacement needs to handle before quoting, which includes a load calculation and a check of the service entrance. If the meter and service entrance need updating at the same time, that gets scoped together.
A breaker that trips under load is doing its job. A breaker that trips randomly, at low load, or only sometimes is harder to pin down. We trace the circuit, check connections, test the breaker itself, and look for wiring conditions that could be causing the fault before recommending a fix. Intermittent faults take longer to diagnose than straightforward ones, and we say so on the call so the visit is scoped correctly.
A staircase, a hallway, or a long garage where the light needs to be controlled from both ends requires three-way switching. When that wiring was done incorrectly or was never finished, the result is a switch that works from one location but not the other, or a circuit that behaves unpredictably. We trace the existing wiring, identify where the problem is, and correct it without pulling more wire than the job requires.
Aluminum branch-circuit wiring from the 1960s and 1970s is present in a portion of the older housing stock in this area. The risk is not in the wire itself but at the connections, where aluminum meets devices rated for copper only. Remediation addresses each connection point with approved methods, either by pigtailing with copper or by replacing devices with ones rated for aluminum. We assess the scope on the call and confirm the price before scheduling.
Most lighting requests fall into one of two categories: something that stopped working, or something that was never quite right to begin with. A room with a single overhead fixture and no dimmer is a common complaint in older homes. Recessed LED installations, pendant replacements, and dimmer switch upgrades are all work that can be done on a single visit, and they are worth combining when other electrical work is already scheduled in the same area.
Recessed can lights require a correctly rated junction box, a circuit that can carry the added load, and clean wiring runs that do not interfere with insulation. Under-cabinet lighting in a kitchen is a different scope but follows the same principle: the right circuit, the right connection, and a finish that does not look like an afterthought. We confirm what the existing circuit can support before any fixture work begins.
Exterior lighting needs weatherproof boxes, conduit or direct-burial cable rated for outdoor use, and GFCI protection at the source. Motion sensor lights, soffit lighting, and driveway fixtures each have their own placement and wiring requirements. If a security light is going up at the same time as other exterior work, that is the right time to run the circuit, because the wall is already open or the trench is already dug. Each service is described in more depth on our list of electrical services.
We are available every day from 6:30 AM to 10:00 PM. For most jobs, the visit is scoped on the call, the price is confirmed, and an appointment is set based on what the schedule allows. Ask what is available when you call and we will tell you directly.
For problems that cannot wait, describe what you are seeing when you call. A panel that is buzzing and warm, an outlet that sparked and stopped working, or a partial power loss after a storm are all situations that move to the front of the schedule. We do not ask a business to close or a tenant to leave for work that can be done in stages. When the job requires the circuit to be off, we confirm how long that takes and plan around it.
One call is enough to get the visit booked.
A landlord booking electrical work for a rental has a different set of needs than a homeowner. The person who books the job is usually not the person who lets us in. We work through that on the call: who has access, how the tenant will be notified, and what the window for the visit looks like. We do not show up unannounced at an occupied unit.
After the work is done, the landlord gets a clear account of what was found, what was corrected, and what the circuit or panel looks like now. For property managers running several units, an electrical safety inspection gives a documented baseline for each property. That record matters when a tenant raises a concern or when a building changes hands. Reach out and we'll start at the panel.
Payson is the base of the calls we take in this part of Utah County, but the coverage runs wider. We handle electrical work in Spring Lake, West Mountain, Elk Ridge, Salem, and Benjamin, and across the county more broadly. If your address is nearby and you are not sure whether it falls within range, ask on the call. Call now and we'll get the power back where it belongs.
It depends on what the main panel is currently carrying and how much load the outbuilding will add. If there is room in the panel and the service entrance can carry the additional draw, a subpanel feed can be run without a full panel upgrade. If the panel is already near capacity, the upgrade and the subpanel work get scoped together. We confirm which situation applies before quoting the job.
Yes. We work with landlords and property managers on single-family rentals, duplexes, and small multi-unit buildings throughout Payson and the surrounding communities. The booking process accounts for tenant access and scheduling, and we provide a written account of the work done so the property owner has a record on file.
Homes that have been added onto or rewired in sections tend to show up with mismatched wiring, circuits that share a breaker they were never meant to share, and panels that have run out of room. Aluminum wiring remediation and panel replacement come up regularly in the older housing stock here. An electrical safety inspection is a practical starting point when the history of the wiring is unclear.
When you call, we ask about the symptom, the location, and what you already know about the panel and the wiring. By the end of that call, you know what the visit involves, what it costs, and when it can be scheduled.
Call (385) 452-6995 to get started.
Electrical work in the surrounding towns: Salem, Spanish Fork, Mapleton, Springville, Provo. For every town we reach, see our service map.
Below is a plain-language look at the electrical services we handle across Payson and Utah County. Each row covers what the work involves, who it fits best, and one practical note worth knowing before you call. If a job spans more than one category, we scope it together on the phone so nothing gets missed.
| Service | What's Included | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Lighting Installation |
| Homeowners updating interior lighting or adding exterior security and landscape fixtures | Outdoor fixtures need weatherproof boxes and GFCI protection at the source, not just a standard interior setup. |
| Outlet & Switch Installation |
| Homeowners upgrading protection in kitchens, baths, garages, and outdoor locations | GFCI protection is a code requirement in kitchens, bathrooms, garages, and all exterior locations, not just a nice-to-have. |
| Electrical Panel & Service Upgrades |
| Homes adding an EV charger, heat tape circuits, or major appliances that push a 100-amp panel past its limit | Older Payson homes are often still on 100-amp service, which was sized for a fraction of the load that modern appliances, EV chargers, and heat tape circuits now demand. |
Call (385) 452-6995 between 6:30 AM and 10:00 PM any day of the week and we will go through your job with you, confirm the scope, and give you a price before anything is scheduled.
(385) 452-6995