When a renovation, an addition, or a new appliance enters the picture, the electrical side of the project needs to be right before anything else moves forward. Oscar's Electric handles that work for homeowners and businesses in Spanish Fork, from running dedicated circuits ahead of a kitchen remodel to upgrading a panel that has run out of room. Whether the job is planned weeks out or needs to happen this week, we put licensed electricians on it and do the work to code.
Spanish Fork is a city where the housing stock runs the range, from older homes on original wiring to newer builds with modern panels. We handle both ends of that range and everything between. Call (385) 452-6995 to get a quote and find out when we can be out.
The lighting calls we get most often in Spanish Fork split between interior fixture work and outdoor security and perimeter lighting. Inside, that means recessed lighting layouts, ceiling fan installation, pendant and chandelier wiring, dimmer switches, and under-cabinet lighting for kitchens and workspaces. A room that was wired for a single overhead fixture rarely has enough circuits to do what a modern lighting plan asks of it, and we handle the circuit work that makes the upgrade possible.
Outside, we wire motion sensor lights, driveway and entry fixtures, deck and patio lighting, and security lighting for garages and outbuildings. If a renovation or addition is already opening walls or ceilings, that is the right time to add exterior runs and conduit rather than cutting into finished surfaces later. Electrical work done to the standard the next inspection expects means the lighting goes in once and stays.
Code-compliant wiring on every job covers the grounding and bonding details that get missed when fixture installation is treated as a simple swap. We make sure the box is rated for the load, the ground is connected, and the circuit is sized for what is being added.
Same-day service is often available for both repairs and installations across Spanish Fork and the surrounding area. When you call (385) 452-6995, you get a rate before anything is scheduled and a clear picture of what the job involves. There is no obligation to move forward until you know what it covers and what it costs.
For problems that will not keep, we work around what is already happening at the property. A tenant who cannot lose power mid-day, a business that needs to stay open, a repair that has to happen before a showing: those situations are part of what we plan around. Qualified electricians for every job means the person who shows up is ready to handle what was described on the call, not just assess it.
We are open every day from 5:00 AM to 8:30 PM. Reach out and an electrician will follow up.
A full rewire is the right call when the existing wiring is deteriorated, undersized for current loads, or built on a system that was never grounded. Partial rewires make sense when a remodel opens specific walls or when a section of the home needs to be brought up to code without touching the rest. We assess what is there, explain what the job involves, and do the work correctly rather than patching around a problem that will surface again.
Knob-and-tube wiring lacks a ground conductor and was not designed for the loads a modern home carries. It also cannot be buried in insulation without creating a heat buildup risk, which matters in a region where well-insulated walls are standard. We replace knob-and-tube circuits with properly grounded, code-compliant wiring, and we handle the permit work that goes with it.
A panel where half the breakers are unlabeled or mislabeled is a problem that shows up every time someone needs to isolate a circuit safely. We trace circuits, label them accurately, and document what feeds what. This work often surfaces other issues, like double-tapped breakers or circuits that were added without being properly integrated into the panel.
Electric ranges, dryers, EV chargers, hot tubs, and workshop equipment all need circuits sized for the load they draw. Running a heavy appliance on a shared circuit causes repeated trips, accelerates wear on the breaker, and creates conditions that are genuinely unsafe over time. We size and install dedicated circuits to match the equipment, and we confirm the panel has the capacity before the circuit goes in.
A generator without a proper transfer switch is a hazard for utility workers and for the equipment it is feeding. We wire transfer switches, both manual and automatic, and connect generators to the panel so backup power flows cleanly and safely when the grid goes down. The electrical side of this job is what we handle. We protect your floors and finishes while we work, and we leave the space clean when it is done.
When the incoming power supply to a home or building needs to be brought up to current capacity, the work starts at the service entrance. We handle meter base replacements, service-entrance cable upgrades, and the coordination with the utility that goes with them. This work is often part of a larger panel upgrade, and we handle both together when the job calls for it.
Anyone weighing up a job in Spanish Fork may want the electrical repair page first.
When you call, the conversation starts with what the job involves. You get a rate on the phone before anything is scheduled, and you are told what it covers. If the scope is straightforward, that is usually enough to confirm the appointment. If the job needs a closer look first, we say so upfront and explain why.
What changes a quote is usually what the job reveals once it starts. Hidden wiring, a panel that needs remediation before the new circuit can go in, or a situation where the original scope turns out to be part of a larger problem: those conversations happen before the work proceeds, not after. You know what it costs before we move forward.
The service page carries the full breakdown of what each type of job involves. For a specific quote on your situation in Spanish Fork, call (385) 452-6995.
The repair calls that come out of a city like Spanish Fork tend to fall into a few categories. Outlets that stop working, breakers that trip under normal use, lights that flicker without an obvious cause, and burning smells near receptacles or panels are all signs of something that needs to be traced and fixed rather than reset and ignored. We diagnose before we repair, which means finding the actual source rather than replacing parts until the symptom goes away.
Older homes in this area were wired for a fraction of the electrical load a modern household puts on a panel. Add an EV charger, updated appliances, a home office, and heat tape circuits for winter, and a 100-amp panel runs out of room fast. We assess the current capacity, explain the options, and install the upgrade that matches what the home or building actually needs. Electrical work here gets handled by people who answer to this community.
New circuits, added outlets, ceiling fans, EV charger wiring, exterior lighting, and circuits for workshop equipment or new appliances all start with a call to confirm what the job involves and whether the panel can support it. Installation work is often planned ahead, which makes scheduling straightforward. We confirm the scope on the call and set a time that works around what is already happening at the property.
The service page carries the full list of what we handle and what each type of job involves.
We serve Spanish Fork and the communities around it throughout Utah County. Palmyra, Mapleton, Springville, Salem, and Benjamin are all covered, along with the broader county area for both residential and commercial work. If you are in the area and need an electrician, call (385) 452-6995 to confirm service at your address and get a quote.
We still inspect the most likely sources based on what you described. If the fault is intermittent and nothing shows up during the visit, we walk you through what to note the next time it happens, such as the time of day, what was running, and whether anything tripped, so the next call gives us more to work with.
It is a good idea to keep pets away from the work area while the job is in progress. Open panels, pulled wiring, and tools on the floor are hazards for animals that get underfoot. We do not require it, but most customers find it easier to keep pets in a separate room for the duration.
Yes. Kitchen circuits, including dedicated circuits for the range, dishwasher, refrigerator, and countertop outlets, are much easier to run before cabinetry and appliances are in place. Coordinating the electrical work with the kitchen installation schedule avoids having to open finished surfaces later.
We handle permit coordination as part of the job. You do not need to contact the building department yourself. The permit is pulled before the work starts, and the inspection is scheduled as part of completing the job correctly.
A documented electrical inspection covering the panel, wiring condition, GFCI and AFCI protection, and any code violations gives a landlord a clear record of the property's condition. We conduct those inspections and can follow up with remediation if the inspection identifies work that needs to be done before the next tenant moves in.
We confirm the panel has open slots, that the existing service is sized to carry the added load, and that the wiring path to the new circuit location is workable. If the panel is already at capacity or the service is undersized, we address that before the new circuit goes in.
The framing needs to be complete and the layout confirmed before rough-in wiring begins. Panel location, service entry point, and the locations of fixtures, outlets, and switches should be agreed on in advance. We coordinate with the general contractor on sequencing so the electrical work fits into the broader project schedule.
Yes. We cover Spanish Fork and the surrounding Utah County communities, including Mapleton, Springville, Salem, Benjamin, and Palmyra. Call (385) 452-6995 to confirm service at your specific address and get a quote for the job.
Before the walls close is the right answer. Running circuits, adding outlets, roughing in for lighting, and sizing the panel for the added load all need to happen while the framing is accessible. Calling early in the planning process means the electrical side does not become a problem that delays everything else.
Older homes in the area frequently have panels that were sized for a much lighter load than a modern household puts on them, along with circuits that were added over the years without being properly integrated. Knob-and-tube wiring, unlabeled breakers, and outlets that were never grounded are common findings too. A call is the fastest way to describe what you are seeing and find out what it points to.
Outlets and lighting in the same room are often on separate circuits, so a dead outlet circuit does not always mean the breaker has tripped. The first thing to check is whether a GFCI outlet on the same circuit has tripped, since one tripped GFCI can cut power to several downstream outlets. If that is not the issue, the circuit itself needs to be traced and tested.
Describing what is happening is enough. Oscar's Electric handles electrical repairs, panel upgrades, rewiring, lighting, EV charger circuits, generator hookups, and more for homes and properties across Spanish Fork. We are open every day from 5:00 AM to 8:30 PM. Call (385) 452-6995 and tell us what you are seeing. We will take it from there.
We also take work in: Springville, Provo, Vineyard, Pleasant Grove, American Fork.
View our coverage map.
We handle the full range of electrical work for homes and businesses across Spanish Fork and Utah County, from a tripped breaker or dead outlet to a full panel upgrade or generator hookup. The table below breaks down what each service covers, who it fits best, and what is worth knowing before you call. Same-day service is often available, and we are open every day from 5:00 AM to 8:30 PM. Call (385) 452-6995 to get a quote on any of the services listed here.
| Type of Work | Scope of Work | When You Need It | Things to Know |
|---|---|---|---|
| Backup Generator Installation |
| Homeowners and businesses in Utah County who need power during winter outages | A transfer switch is required. Without one, backfeeding power into the grid is a serious hazard for utility workers and your own equipment. |
| Whole-Home Surge Protection |
| Homes with smart devices, home offices, or expensive appliances worth protecting | A single surge event can damage refrigerators, HVAC controls, and anything else plugged in. Panel-level protection catches spikes before they reach your devices. |
| Heat Tape Installation |
| Spanish Fork homes with exposed pipes in garages, crawl spaces, or exterior walls | Heat tape on an improperly wired or overloaded circuit is a genuine fire hazard. The electrical side has to be done right. |
| Outlet & Switch Installation |
| Homeowners adding outlets, upgrading kitchens or baths, or replacing worn receptacles | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor areas. We install to current code on every job. |
| Breaker & Fuse Repair |
| Homes with frequently tripping breakers or older fuse-based panels | A breaker that trips repeatedly under normal load is a symptom, not just an annoyance. We find out what is causing it. |
| Dedicated Appliance Circuits |
| Anyone adding a major appliance or workshop equipment that needs its own circuit | Running a heavy appliance on a shared circuit causes repeated trips and wears out wiring faster than it should. |
| Electrical Repairs & Troubleshooting |
| Any homeowner or business with an unexplained electrical problem | We diagnose before we repair, tracing the actual source rather than swapping parts at random. |
| Ceiling Fan Installation |
| Bedrooms, living rooms, and covered outdoor spaces | Ceiling fans require a rated electrical box. We confirm the box is correct before the fan goes up. |
| Electrical Safety Inspections |
| Buyers, landlords, property managers, and anyone whose carrier requires documentation | When an inspection turns up problems, we handle the remediation as well. Permit work is part of the process when the job requires it. |
| Wiring & Circuit Installation |
| Older homes with outdated wiring, remodels that open walls, and any project adding new circuits | Knob-and-tube and deteriorated aluminum branch circuits do not meet current code and carry real safety risks. We assess and explain the options before quoting. |
| Electrical Panel & Service Upgrades |
| Older homes being remodeled, homes adding EV chargers, or any property where breakers trip too often | Licensed electricians pull the permits, do the work to code, and see it through inspection. Permit work is part of the job. |
| Lighting Installation |
| Homeowners updating interior or exterior lighting, and businesses upgrading to efficient fixtures | We run new wiring where needed rather than just swapping fixtures, so the result is safe and up to code. |
Call (385) 452-6995 to talk through any of these services, get a quote, or schedule an appointment. We are available every day from 5:00 AM to 8:30 PM.
(385) 452-6995